On a slightly sloping terrain, with a somewhat soft lawn after the spring rains, you quickly end up with a pool that tilts and a structure under tension. The Intex 58983 Metal Frame pool, like any above-ground tubular pool, does not forgive soil imperfections. Before taking the tubes out of the box, it’s the ground that determines the success of the assembly.
Unstable ground and Intex tubular pool: what the terrain imposes
The first reflex, often overlooked, is to check the flatness of the ground with a level on a mason’s rule. A difference of a few centimeters across the width of the pool is enough to create asymmetric pressure on the metal supports. Feedback varies on this point, but beyond two centimeters of elevation difference, there is a risk of liner deformation and premature wear of the fittings.
Read also : How to Quickly Fix Your Android Smartphone in Case of Malfunction or Damage
We are talking about a compact and stable ground here. Freshly turned soil, loose sand, or waterlogged grass are not suitable. You need to strip the vegetation layer over the entire footprint of the pool, then level the ground flat. A bed of fine sand, well-leveled and compacted with a roller, remains the best base to protect the bottom of the liner from stones and roots.
If you plan to install an Intex 58983 metal frame pool on an existing concrete slab, it is often the most reliable solution in terms of flatness. Just remember to place a ground mat or thick geotextile in between to prevent direct abrasion of the liner on the concrete.
Recommended read : How to easily convert 60 ml to cl to succeed in all your recipes
- Remove stones, roots, and debris from the entire surface, plus a margin of a few dozen centimeters around
- Check the flatness in both axes (length and width) before unrolling the liner
- Avoid areas close to trees: roots rise up and pierce the ground mat in one season
- Never install on sloping ground without prior leveling, even slightly
Assembly of the Metal Frame structure: order of operations and common mistakes
The Intex manual details a precise order for assembling the tubes. You start by unfolding the liner on the ground, in full sun if possible, so that the PVC softens and is easier to handle. The storage folds disappear in about twenty minutes under the heat.
The horizontal tubes fit into the sewn loops at the top of the liner. Then come the vertical supports, fitted into the T-connectors. The classic mistake is to start filling before checking the alignment of all the supports. Once the water is in the pool, correcting a misaligned foot becomes very complicated.
Progressive filling, not all at once
You fill a few centimeters, then walk around the pool to smooth out the folds of the liner and reposition the structure. Folds trapped under water become friction areas that weaken the bottom.
Filling in increments of about ten centimeters also allows you to detect a leak at the filtration fittings before the pool is full. It’s better to empty twenty liters than several hundred.
Water restrictions and regulations before filling
During the summer, prefectural orders may prohibit the filling of private pools when the department goes on drought alert. These restrictions also apply to above-ground pools, including removable models like the Metal Frame.
Before planning to fill the pool, check the prefectural orders in effect in your department. In areas of heightened alert, initial filling may be completely prohibited, with very limited exceptions (pools under construction requiring filling, therapeutic uses).
Regarding taxation, removable above-ground pools that do not require leveling work are generally exempt from development tax and have no impact on property tax. No declaration at the town hall is required, unless the land is located in a protected area (protected sector, classified site, nature park).
Filtration and maintenance of the Intex 58983 liner: keeping the water clear
The filtration pump supplied with the kit is sized for the volume of the pool, but it reaches its limits in the height of summer when the water temperature rises. Run the filtration at a minimum during the hottest hours of the day, not at night when the water cools.
The filter cartridge clogs quickly if you don’t rinse your feet before entering the pool. A simple footbath or a water jet next to the ladder reduces the load of organic debris in the water.
- Rinse the filter cartridge every two to three days during high season, and replace it as soon as it no longer regains its original color after rinsing
- Check the pH once or twice a week with strips: an unbalanced pH makes the disinfectant treatment ineffective
- Cover the pool at night with a suitable tarp to limit evaporation and pollution from insects or leaves
Winterizing or complete storage
The Metal Frame 58983 is a removable pool. At the end of the season, empty it, clean the liner with clear water (never abrasive products), and let it dry completely before folding. A damp stored liner develops mold that makes it brittle during the next unfolding.
The metal tubes should be stored away from moisture. A garage or a closed garden shed is suitable, provided the parts are dry. Checking the O-rings and connectors before storage allows you to identify parts to replace before the next season, while they are still available in stock.
The lifespan of the liner directly depends on the care taken in winter storage and the quality of the ground under the pool. A worn ground mat or poorly prepared terrain accelerates wear much more than exposure to sunlight or chemicals.